Autronica BS-320 User's Guide Page 124
- Page / 132
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Appendix
Operator's Handbook, AutroSafe Interactive Fire Alarm System, Release 3, ASAFE-FO/FE Rev. I, 2009-02-27,
Autronica Fire and Security AS
Page 122
15.3 Action Digits Table - Operation Mode
All action digits that may appear in Operation Mode are listed in the
table below.
Action Digits
Action Digit When action is available Used to…..
ACCEPT FIRE
WARNING
4
JKL
Available when the selected event is a
non-accepted Fire Warning.
• accept the selected Fire
Warning.
ACCEPT FAULT
WARNING
3
GHI
Available in the Info window when the
selected event is a non-accepted
Fault Warning.
• accept the selected Fault
Warning.
RESOUND
1
ABC
Available in the event of a fire alarm
when alarms have been silenced.
• resound all Fire Alarm
Devices (FAD) related to the
alarms within the operation
zone of the operator panel.
REACTIVATE
3
GHI
Available when there exists alarm
disabled points
• reactivate (enable) the alarm
disabled points.
ACTIVATE
2
DEF
Available when one or several
Delayed Action detection zones have
entered a fire alarm state and are in
their T1 and T2 periods.
(Not included in SOLAS version).
• immediately activate the
delayed actions of all active
Delayed Action detection
zones.
SHOW POINTS
1
ABC
Available when the selected event is a
Detection Zone.
• show point information.
SHOW SUPPR.
INFO
4
JKL
Available when conditions are active,
but suppressed.
• show suppressed information
if other conditions are active,
but suppressed.
SHOW FIRE
INFO
1
ABC
Available during a fire alarm condition
when Show Suppressed Information
has been pressed.
• show suppressed fire
information
SHOW FIRE
WARNING
1
ABC
Available during a fire alarm condition
when Show Suppressed Information
has been pressed and there exists fire
warnings.
• show suppressed fire
warnings
SHOW FAULT
WARNING
2
DEF
Available during a fire alarm condition
when Show Suppressed Information
has been pressed and there exists
fault warnings.
• show suppressed fault
warnings
SHOW
DISABLEMENTS
3
GHI
Available during a fire alarm condition
when Show Suppressed Information
has been pressed and there exists
disablements.
• show suppressed
disablements
SHOW TESTS
4
JKL
Available during a fire alarm condition
when Show Suppressed Information
has been pressed and there exists
tests.
• show suppressed tests
ENABLE
3
GHI
Available when the selected event is a
disablement.
• enable the disablement.
Continues on next page…
- Operator's Handbook 1
- Table of Contents 3
- 1. Introduction 7
- 1.4 Components 8
- 2.1 Introduction 9
- 2.2 Indication Devices 10
- 2.3 The Menu Display 12
- 2.4 Operating Buttons 13
- 2.4.2 Front Push Buttons 14
- 2.4.3 Alphanumeric Keyboard 14
- 2.5 Internal Buzzer 15
- 3. Operation Mode 16
- 3.3 Alarm Levels 17
- 3.4 Access Levels 17
- Operation Mode 18
- (default) 19
- FIRE ALARMS 20
- SHOW STATUS 21
- FIRE ALARM INFO 22
- 3.13 Resetting the System 24
- 3.15 Suppressed Information 25
- 3.16 Disablement Sources 25
- 3.16.2 Point Disablements 26
- 3.18.1 Introduction 28
- About «In the Event of….» 34
- In the Event of a Fire Alarm 36
- twice 37
- with Alarm Delay 40
- DISABLEMENTS 42
- AUTROSAFE 46
- SelfVerify 46
- 8. In the Event of Faults 47
- Actions to be 48
- 9. Menu Mode 50
- Figure 9-2: Disable Menu 52
- Menu Mode 54
- 10. Show Status 56
- 10.5 Show Status - Faults 59
- 11. Disabling 65
- 11.6 Disabling Points 67
- 11.9 Disabling Outputs 67
- Disabling 68
- Disable Menu 69
- 12. Enabling 71
- 12.5 Enabling Points 72
- 12.8 Enabling Outputs 73
- Enable Menu 74
- 13. System Menu 76
- System Menu 78
- 13.5.1 Introduction 79
- 13.5.2 Enter Access Level 3 80
- 13.5.3 Leave Access Level 3 80
- 13.6 How to Feed Paper 82
- 13.7 How to Change Language 83
- 13.9 Day / Night Timers 85
- Menu, press the Close button 86
- 14. Service Commands 87
- 14.3 Testing 88
- 14.3.1.3 Leaving Test Mode 92
- 14.3.2 Testing Outputs 94
- 14.3.2.1 Manual Test ON 94
- Protection Equipment 98
- 14.3.2.6 Manual Test OFF 99
- Service Commands 100
- Figure 14-3: Log Menu 102
- 14.4.1 Events 103
- Page 102 104
- Page 103 105
- 14.4.3 Logging All Events 106
- 14.4.4 The Log Setup Menu 107
- Clear Log 108
- Page 107 109
- Page 108 110
- Page 109 111
- 14.5 Loop Commands 112
- 14.5.2 Disable Loop 113
- 14.5.3 Enable Loop 114
- 14.6 Report 115
- POINT LOCATION 116
- 14.6.2 Polluted 117
- 15. Appendix 119
- Appendix 120
- Page 118 120
- 15.2 Zonal Definitions 121
- 15.2.3 Alarm Zone 122
- 15.2.4 Operation Zone 122
- Page 121 123
- Action Digits 124
- Page 123 125
- 15.4 Menu Structure 126
- 16. Index 127
- 17. Figure List 128
- 18. Reader’s Comments 129
Related products and manuals for Fire protection Autronica BS-320
(64 pages)© 2020, manymanuals.com. All rights reserved. | 0.749 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals