Autronica BS-320 User's Guide Page 49
- Page / 132
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
In the Event of Faults
Operator's Handbook, AutroSafe Interactive Fire Alarm System, Release 3, ASAFE-FO/FE Rev. I, 2009-02-27,
Autronica Fire and Security AS
Page 47
Ste
p
Actions to be
taken
Display Indication Audible Indication
6
To view all points in fault
warning state within the
selected detection zone,
press Action Digit 1
(SHOW POINTS).
Comments: In this example, detection zone «OFFICES» is selected. All points in fault
warning state within this zone are shown.
7
Select the point to be
accepted by scrolling
with the arrow buttons (if
there are several points
in fault warning state),
then press
8
To accept the selected
point, press Action Digit
3 (ACCEPT FAULT
WARNING).
Comments: In this example, point P5 in the selected detection zone is accepted. If there
are several points in fault warning state in this detection zone, each one can
be accepted in turn by repeating step 7, 8 and 9.
Fault warnings that are accepted, will no longer blink in the display. This allows
you to see on the screen whether a fault warning is accepted or not.
A fault that has been repaired is indicated with a star on the display (for
example, 1*OFFICES).
When all fault warnings are accepted, the yellow Fault indicator will switch
from blinking to steady light.
If all faults are repaired and accepted, the panel will enter its idle state.
If all fault warnings are accepted, but one or several faults are still not
repaired, the panel will return to its idle state as soon as the remaining faults
are repaired.
In some cases it may be necessary to reset the system to remove fault
warnings.
If the system detects any irregularity on the loop topology (for example, two
detectors have changed places or are removed), the panel will enter its idle
state as soon as the detectors are in placed in their correct positions according
to the configuration.
SHOW STATUS
FAULTS (points)
OFFICES
Received: 19:23:50
POINT:
P5
P6
P2
19:23
SHOW STATUS
FAULTS (points)
OFFICES
Received: 19:23:50
POINT:
P5
P6
P2
19:23
FAULT INFO
19:23
3: ACCEPT FAULT WARN.
UNIT IN FAULT:
POINT 3
TYPE:
Point
Point not responding
(REPORTED BY (F/L/S):
FAULT INFO
19:23
3: ACCEPT FAULT WARN.
UNIT IN FAULT:
POINT 3
TYPE:
Point
Point not responding
(REPORTED BY (F/L/S):
ACCEPT FAULTACCEPT FAULT
SHOW STATUS
FAULTS (points)
OFFICES
Received: 19:23:50
POINT:
P5
P6
P2
19:23
SHOW STATUS
FAULTS (points)
OFFICES
Received: 19:23:50
POINT:
P5
P6
P2
19:23
AUTROSAFE
SelfVerify
AUTROSAFE
SelfVerify
- Operator's Handbook 1
- Table of Contents 3
- 1. Introduction 7
- 1.4 Components 8
- 2.1 Introduction 9
- 2.2 Indication Devices 10
- 2.3 The Menu Display 12
- 2.4 Operating Buttons 13
- 2.4.2 Front Push Buttons 14
- 2.4.3 Alphanumeric Keyboard 14
- 2.5 Internal Buzzer 15
- 3. Operation Mode 16
- 3.3 Alarm Levels 17
- 3.4 Access Levels 17
- Operation Mode 18
- (default) 19
- FIRE ALARMS 20
- SHOW STATUS 21
- FIRE ALARM INFO 22
- 3.13 Resetting the System 24
- 3.15 Suppressed Information 25
- 3.16 Disablement Sources 25
- 3.16.2 Point Disablements 26
- 3.18.1 Introduction 28
- About «In the Event of….» 34
- In the Event of a Fire Alarm 36
- twice 37
- with Alarm Delay 40
- DISABLEMENTS 42
- AUTROSAFE 46
- SelfVerify 46
- 8. In the Event of Faults 47
- Actions to be 48
- 9. Menu Mode 50
- Figure 9-2: Disable Menu 52
- Menu Mode 54
- 10. Show Status 56
- 10.5 Show Status - Faults 59
- 11. Disabling 65
- 11.6 Disabling Points 67
- 11.9 Disabling Outputs 67
- Disabling 68
- Disable Menu 69
- 12. Enabling 71
- 12.5 Enabling Points 72
- 12.8 Enabling Outputs 73
- Enable Menu 74
- 13. System Menu 76
- System Menu 78
- 13.5.1 Introduction 79
- 13.5.2 Enter Access Level 3 80
- 13.5.3 Leave Access Level 3 80
- 13.6 How to Feed Paper 82
- 13.7 How to Change Language 83
- 13.9 Day / Night Timers 85
- Menu, press the Close button 86
- 14. Service Commands 87
- 14.3 Testing 88
- 14.3.1.3 Leaving Test Mode 92
- 14.3.2 Testing Outputs 94
- 14.3.2.1 Manual Test ON 94
- Protection Equipment 98
- 14.3.2.6 Manual Test OFF 99
- Service Commands 100
- Figure 14-3: Log Menu 102
- 14.4.1 Events 103
- Page 102 104
- Page 103 105
- 14.4.3 Logging All Events 106
- 14.4.4 The Log Setup Menu 107
- Clear Log 108
- Page 107 109
- Page 108 110
- Page 109 111
- 14.5 Loop Commands 112
- 14.5.2 Disable Loop 113
- 14.5.3 Enable Loop 114
- 14.6 Report 115
- POINT LOCATION 116
- 14.6.2 Polluted 117
- 15. Appendix 119
- Appendix 120
- Page 118 120
- 15.2 Zonal Definitions 121
- 15.2.3 Alarm Zone 122
- 15.2.4 Operation Zone 122
- Page 121 123
- Action Digits 124
- Page 123 125
- 15.4 Menu Structure 126
- 16. Index 127
- 17. Figure List 128
- 18. Reader’s Comments 129
Related products and manuals for Fire protection Autronica BS-320
(64 pages)© 2020, manymanuals.com. All rights reserved. | 1.088 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals