Autronica BS-320 User's Guide Page 90
- Page / 132
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Service Commands
Operator's Handbook, AutroSafe Interactive Fire Alarm System, Release 3, ASAFE-FO/FE Rev. I, 2009-02-27,
Autronica Fire and Security AS
Page 88
14.3.1.2 Entering Test Mode
To be able to manually test points (detectors or manual call-points)
without automatic actioning of Fire Protection Equipment (FPE), Fire
Alarm Routing Equipment (FARE) or Fire Alarm Devices (FAD),
detection zones can be set in test mode (ENTER TEST MODE). If a
detection zone has been set to test mode, any point connected to this
zone can be tested (with, for example, test gas) without automatic
actioning (i..e. audible indication) from sounders, bells, etc.
In the SHOW STATUS menu (main menu selection 1), you can now
verify that a point you have tested (for example, a detector you have
tested with test gas) operates properly - without audible indication.
As shown on the example below, a message on a status line will
appear (Alarm test), indicating that the alarm signal has been sent
from the tested point (in this example, P2, optical detector).
SHOW STATUS
19:23
DETECTION ZONES IN TEST(points)
1 CANTEEN
Received: 10:16:26
POINT: TYPE: ALARM STATE:
P2 Optical Alarm test
FIRE ALARMS Total: 1
3 CANTEEN
Figure 14-3: Show zones in test/points
The zones in test mode will always appear on the display. From here,
you can also enter the SHOW STATUS menu directly.
In test mode, the automatic timeout (default 25 seconds in operation
mode / menu mode) is 20 times the default timeout (i.e. up to 500
seconds) provided that no alarms occur within the timeout period.
The procedure below describes how to set a detection zone in test
mode.
Step Actions to be taken Display Indication
1
To enter the Main Menu, press
MENU
19:23
Total: 3
1 SHOW STATUS
2 DISABLE
3 ENABLE
4 SYSTEM
5 SERVICE
- Operator's Handbook 1
- Table of Contents 3
- 1. Introduction 7
- 1.4 Components 8
- 2.1 Introduction 9
- 2.2 Indication Devices 10
- 2.3 The Menu Display 12
- 2.4 Operating Buttons 13
- 2.4.2 Front Push Buttons 14
- 2.4.3 Alphanumeric Keyboard 14
- 2.5 Internal Buzzer 15
- 3. Operation Mode 16
- 3.3 Alarm Levels 17
- 3.4 Access Levels 17
- Operation Mode 18
- (default) 19
- FIRE ALARMS 20
- SHOW STATUS 21
- FIRE ALARM INFO 22
- 3.13 Resetting the System 24
- 3.15 Suppressed Information 25
- 3.16 Disablement Sources 25
- 3.16.2 Point Disablements 26
- 3.18.1 Introduction 28
- About «In the Event of….» 34
- In the Event of a Fire Alarm 36
- twice 37
- with Alarm Delay 40
- DISABLEMENTS 42
- AUTROSAFE 46
- SelfVerify 46
- 8. In the Event of Faults 47
- Actions to be 48
- 9. Menu Mode 50
- Figure 9-2: Disable Menu 52
- Menu Mode 54
- 10. Show Status 56
- 10.5 Show Status - Faults 59
- 11. Disabling 65
- 11.6 Disabling Points 67
- 11.9 Disabling Outputs 67
- Disabling 68
- Disable Menu 69
- 12. Enabling 71
- 12.5 Enabling Points 72
- 12.8 Enabling Outputs 73
- Enable Menu 74
- 13. System Menu 76
- System Menu 78
- 13.5.1 Introduction 79
- 13.5.2 Enter Access Level 3 80
- 13.5.3 Leave Access Level 3 80
- 13.6 How to Feed Paper 82
- 13.7 How to Change Language 83
- 13.9 Day / Night Timers 85
- Menu, press the Close button 86
- 14. Service Commands 87
- 14.3 Testing 88
- 14.3.1.3 Leaving Test Mode 92
- 14.3.2 Testing Outputs 94
- 14.3.2.1 Manual Test ON 94
- Protection Equipment 98
- 14.3.2.6 Manual Test OFF 99
- Service Commands 100
- Figure 14-3: Log Menu 102
- 14.4.1 Events 103
- Page 102 104
- Page 103 105
- 14.4.3 Logging All Events 106
- 14.4.4 The Log Setup Menu 107
- Clear Log 108
- Page 107 109
- Page 108 110
- Page 109 111
- 14.5 Loop Commands 112
- 14.5.2 Disable Loop 113
- 14.5.3 Enable Loop 114
- 14.6 Report 115
- POINT LOCATION 116
- 14.6.2 Polluted 117
- 15. Appendix 119
- Appendix 120
- Page 118 120
- 15.2 Zonal Definitions 121
- 15.2.3 Alarm Zone 122
- 15.2.4 Operation Zone 122
- Page 121 123
- Action Digits 124
- Page 123 125
- 15.4 Menu Structure 126
- 16. Index 127
- 17. Figure List 128
- 18. Reader’s Comments 129
Related products and manuals for Fire protection Autronica BS-320
(64 pages)© 2020, manymanuals.com. All rights reserved. | 0.087 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals