Autronica BS-320 User's Guide Page 96
- Page / 132
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Service Commands
Operator's Handbook, AutroSafe Interactive Fire Alarm System, Release 3, ASAFE-FO/FE Rev. I, 2009-02-27,
Autronica Fire and Security AS
Page 94
Step Actions to be taken Display Indication
8
To accept the selected Alarm Zone and activate
the test, press twice on
SERVICE
19:23
MANUAL TEST ON
1 FIRE ALARM DEVICES
2 FIRE PROTECTION EQUIPMENT
3 FIRE WARNING ROUTING EQUIPMENT
4 OTHER OUTPUTS
SERVICE
19:23
MANUAL TEST ON
1 FIRE ALARM DEVICES
2 FIRE PROTECTION EQUIPMENT
3 FIRE WARNING ROUTING EQUIPMENT
4 OTHER OUTPUTS
A test signal will be sent to all Fire Alarm Devices
within the selected Alarm Zone.
14.3.2.3 Manual Test ON- Fire Alarm Routing Equipment (FARE)
The test is similar to the test for Fire Alarm Devices (FAD) and it
requires Access Level 3 (password restricted). For detailed
description, refer to 14.3.2.2.
When the test is initiated, a test signal will be sent to all Fire Alarm
Routing Equipment (FARE) within the Operation Zone (if there are
several Operation Zones, the signal will be sent to FARE in all
Operation Zones). The duration of the signal and the interval between
each signal are configurable (normally 1 second ON and 30 seconds
OFF).
The test signal is given the lowest priority. In the event of an alarm,
the alarm signal will thus override the test signal.
14.3.2.4 Manual Test ON- Fire Warning Routing Equipment (FWRE)
The test is similar to the test for Fire Alarm Devices (FAD) and it
requires Access Level 3 (password restricted). For detailed
description, refer to 14.3.2.2.
When the test is initiated, a test signal will be sent to all Fire Warning
Routing Equipment (FWRE) within the Operation Zone (if there are
several Operation Zones, the signal will be sent to FARE in all
Operation Zones). The duration of the signal and the interval between
each signal are configurable (normally 1 second ON and 30 seconds
OFF).
The test signal is given the lowest priority. In the event of an alarm,
the alarm signal will thus override the test signal.
- Operator's Handbook 1
- Table of Contents 3
- 1. Introduction 7
- 1.4 Components 8
- 2.1 Introduction 9
- 2.2 Indication Devices 10
- 2.3 The Menu Display 12
- 2.4 Operating Buttons 13
- 2.4.2 Front Push Buttons 14
- 2.4.3 Alphanumeric Keyboard 14
- 2.5 Internal Buzzer 15
- 3. Operation Mode 16
- 3.3 Alarm Levels 17
- 3.4 Access Levels 17
- Operation Mode 18
- (default) 19
- FIRE ALARMS 20
- SHOW STATUS 21
- FIRE ALARM INFO 22
- 3.13 Resetting the System 24
- 3.15 Suppressed Information 25
- 3.16 Disablement Sources 25
- 3.16.2 Point Disablements 26
- 3.18.1 Introduction 28
- About «In the Event of….» 34
- In the Event of a Fire Alarm 36
- twice 37
- with Alarm Delay 40
- DISABLEMENTS 42
- AUTROSAFE 46
- SelfVerify 46
- 8. In the Event of Faults 47
- Actions to be 48
- 9. Menu Mode 50
- Figure 9-2: Disable Menu 52
- Menu Mode 54
- 10. Show Status 56
- 10.5 Show Status - Faults 59
- 11. Disabling 65
- 11.6 Disabling Points 67
- 11.9 Disabling Outputs 67
- Disabling 68
- Disable Menu 69
- 12. Enabling 71
- 12.5 Enabling Points 72
- 12.8 Enabling Outputs 73
- Enable Menu 74
- 13. System Menu 76
- System Menu 78
- 13.5.1 Introduction 79
- 13.5.2 Enter Access Level 3 80
- 13.5.3 Leave Access Level 3 80
- 13.6 How to Feed Paper 82
- 13.7 How to Change Language 83
- 13.9 Day / Night Timers 85
- Menu, press the Close button 86
- 14. Service Commands 87
- 14.3 Testing 88
- 14.3.1.3 Leaving Test Mode 92
- 14.3.2 Testing Outputs 94
- 14.3.2.1 Manual Test ON 94
- Protection Equipment 98
- 14.3.2.6 Manual Test OFF 99
- Service Commands 100
- Figure 14-3: Log Menu 102
- 14.4.1 Events 103
- Page 102 104
- Page 103 105
- 14.4.3 Logging All Events 106
- 14.4.4 The Log Setup Menu 107
- Clear Log 108
- Page 107 109
- Page 108 110
- Page 109 111
- 14.5 Loop Commands 112
- 14.5.2 Disable Loop 113
- 14.5.3 Enable Loop 114
- 14.6 Report 115
- POINT LOCATION 116
- 14.6.2 Polluted 117
- 15. Appendix 119
- Appendix 120
- Page 118 120
- 15.2 Zonal Definitions 121
- 15.2.3 Alarm Zone 122
- 15.2.4 Operation Zone 122
- Page 121 123
- Action Digits 124
- Page 123 125
- 15.4 Menu Structure 126
- 16. Index 127
- 17. Figure List 128
- 18. Reader’s Comments 129
Related products and manuals for Fire protection Autronica BS-320
(64 pages)© 2020, manymanuals.com. All rights reserved. | 0.343 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals